CDA WC140 Manuale

Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HYT : 01949 862 012 F : 01949 862 003 E : cu

10DetergentTo fill the detergent compartment1. Push the latch to open the compartment.2. Add the required amount of detergent. The main detergent

11CDA recommends the use of separate detergent, rinse aid and dishwasher salt rather than combination tablets as separates achieve better wash perform

123. Replace the cap and the lower basket.When the “Salt Warning” light on the control panel illuminates, you should refill the salt compartment with s

13If the hardness of the water you use is above 63dE or if you are using well water; you are recommended to use filter and water refinement devices.Plea

14Fig. 4Fig. 5Fig. 6Rinse AidTo fill the rinse aid compartment1. Open the rinse aid compartment by turning and removing the cap as shown in Fig. 4

15Please note: Rinse aid ensures better quality wash results and increased drying performance.Always refill the rinse aid when the rinse aid indicator

16The images below are designed as guidance as to best practice for loading the dishwasher.Upper basketLower basketPoorly stacked loads

17Standard Loading and Test DataCapacity• Upper and lower baskets: 12 place settings.• The upper basket should be adjusted to high position.• Cups sho

18Programmenames andtemperaturesIntensive70°C (P1)Super65°C (P2)Eco50°C (P3)Quick40°C (P4)PrewashNo Heat (P5)Type offood wasteSoups, sauces,pasta, egg

19Warning: Short programmes do not include a drying stage.The values and times provided opposite have been obtained under laboratory conditions accord

2ImportantThe CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note th

20Care and MaintenanceBefore beginning any care or maintenance, you should always disconnect the appliance from the electricity supply, and also turn

21Please note: Never run a programme without the filters in place.Incorrect fitting of the filters may reduce wash performance and potentially damage yo

22Fault CodesThe programme indicators also serve as a diagnostic display to help in the event of a problem with the appliance.Error codeError descript

23Troubleshooting Problem Possible causeThe programme will not startCheck the plug, fuse and circuit breakers of the mains supply.The water tap is tur

24Electrical InformationWarning! This appliance must be earthed.The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To

25As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug

26Fig. 14Fig. 15Fig. 16Installation• Do not install this appliance if it is damaged in any way. Installing a damaged appliance may invalidate the wa

27NOTES:

Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HYT : 01949 862 012 F : 01949 862 003 E : cu

3CE Declarations of Conformity:This appliance has been designed, constructed and marketed in compliance with safety requirements of EEC Directives 200

4Important• Read the instructions prior to installation and use of the appliance.• Do not lean or climb on the open dishwasher door, to prevent da

5• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of

6Control PanelPower ButtonTo switch the power to the dishwasher on or o, press the “Power” button (1). When you switch on the dishwasher, the “End o

7As the delay timer counts down, the “Delay Timer Indicator” lights will illuminate in turn, so at six hours delay the 6h light willilluminate, and at

8Please note: The dishwasher stores the most recently used programme in its memory. To change the programme, simply press the “Programme Selection”

9times and the “End of Programme Indicator” light will switch on. Switching the Dishwasher O• Once the dishwasher beeps five times, and the “End